From: Fenghua Yu
CPU0 or BSP (Bootstrap Processor) has been the last processor that can not
hot removed on x86. This patchset implements CPU0 or BSP online and offline
and removes this obstacle to CPU hotplug.
RAS needs the feature. If socket0 needs to be hotplugged for any reason
thread on socket0 is bad, shared cache issue, uncore issue, etc), CPU0 is
required to be offline or hot replaced to keep the system run. For example,
starting with Core Duo, if you have a system that is reporting cache
via the "yellow" status in the MCi_STATUS msr, then there is benefit in
soft off-lining the cores that share that cache - assuming that leaves you
least one online core. A single socket system with L3 cache troubles is not
helped - but problems in L1/L2 cache, or on multi-socket systems can be
They are already being avoided for the cases where CPU0 is not involved.
This patchset can help L1/L2 cache problem in CPU0 or L3 cache problem on
socket with CPU0 in a multi-socket system.
v9: Add Intel vendor check to support the feature on Intel platforms only.
v8: Add smp_store_boot_cpu_info() and change smp_store_cpu_info() back to
a compilation error. Fix a few messy subject issues.
v7: Change smp_store_cpu_info() to allow store cpuinfo for CPU0 when
Change PIC irq detection in native_cpu_disable().
v6: If CPU0 is offlined during boot time in CPU0 hotplug debug mode, put
online again before resuming from hibernation and disable x2apic and
set __CPUINIT for start_cpu0() in head_32.S. Clean up CPU0 wake up nmi
after callin and callout sync. In a period (3 seconds), check if CPU0 wake
NMI is handled after offlined CPU0 exits from mwait.
v5: Add CONFIG_BOOTPARAM_HOTPLUG_CPU0 and CONFIG_DEBUG_HOTPLUG_CPU0.
duplicate xstate_size init check. Wakeup CPU0 via nmi instead INITs. Add
mcheck_cpu_init when CPU0 online. Change variable bsp_hotpluggable to
cpu0_hotpluggable with __initdata qualifier.
v4: Add __read_mostly for internal bsp_hotpluggable variable. Add my email
address in cpu-hotplug.txt document. A wording change in comment.
v3: Register a pm notifier to check if CPU0 is online before
Small wording changes in document and print info.
v2: Add locking changes between cpu hotplug and hibernate/suspend. Change
irq bound to CPU0 detection.
Fenghua Yu (12):
doc: Add x86 CPU0 online/offline feature
x86, Kconfig: Add config switch for CPU0 hotplug
x86, topology: Don't offline CPU0 if any PIC irq can not be migrated
out of it
x86, hotplug: Support functions for CPU0 online/offline
x86, hotplug, suspend: Online CPU0 for suspend or hibernate
x86-64, hotplug: Add start_cpu0() entry point to head_64.S
x86-32, hotplug: Add start_cpu0() entry point to head_32.S
x86, hotplug: Wake up CPU0 via NMI instead of INIT, SIPI, SIPI
x86, hotplug: During CPU0 online, enable x2apic, set_numa_node.
x86, hotplug: The first online processor saves the MTRR state
x86/i387.c: Initialize thread xstate only on CPU0 only once
x86, topology: Debug CPU00 hotplug
Documentation/cpu-hotplug.txt | 24 ++++++
Documentation/kernel-parameters.txt | 14 +++
arch/x86/Kconfig | 44 ++++++++++
arch/x86/include/asm/cpu.h | 4 +
arch/x86/include/asm/smp.h | 1 +
arch/x86/kernel/cpu/common.c | 5 +-
arch/x86/kernel/cpu/mtrr/main.c | 9 ++-
arch/x86/kernel/head_32.S | 12 +++
arch/x86/kernel/head_64.S | 15 ++++
arch/x86/kernel/i387.c | 6 +-
arch/x86/kernel/smpboot.c | 150
arch/x86/kernel/topology.c | 101 ++++++++++++++++++++++--
arch/x86/power/cpu.c | 82 +++++++++++++++++++
13 files changed, 428 insertions(+), 39 deletions(-)